EMEC FCE 0505 K electromagnetic dosing pump for precise fertilizer injection into the irrigation system. Adjustable dosing 0–100%, body in PVDF+FP+PTFE — resistant to acids, bases and concentrated nutrient solutions.
Plante fertigation delivers nutrients directly into the irrigation water, at the exact moment the plants need them. The system is made up of two units: the EMEC FCE 0505 K/PVDF+FP+PTFE electromagnetic dosing pump — which injects the concentrated fertilizer into the water flow — and an agitation pump installed in the nutrient barrel, which keeps the solution homogeneous and prevents sedimentation.
The assembly is installed in a compact structure made up of a fertigation reservoir, a Plante hermetic panel, the EMEC FCE 0505 K dosing pump and a 36-zone controller, with direct connection to the irrigation system already installed on site.
Acids, bases, oxidizers, saline solutions and concentrated fertilizers
Power supply
220V / 50–60Hz
Hydraulic connection
Ø 4×6mm tube (inlet and outlet)
Manufacturer
EMEC S.r.l. — Italy
Why PVDF + FP + PTFE?
Fertilizer solutions are chemically aggressive — especially those rich in nitrogen, phosphorus and chelated microelements. The PVDF (rigid body) + FP (flexible diaphragm) + PTFE (check valves) combination ensures resistance to the full range of nutrients used in Plante formulations, without degradation or contamination of the solution.
How it works
Precise injection into the irrigation flow.
The EMEC pump injects concentrated fertilizer directly into the water pipe, upstream of the capillary tubes. The injection ratio is set by the front dial from 0 to 100% — with no additional electronics, no external controllers.
Operating cycle
The irrigation system opens the valve and starts the water flow
The agitation pump in the barrel homogenizes the nutrient solution
The EMEC FCE 0505 K injects the concentrated solution in proportion to the flow
The diluted mixture runs through the capillary tubes and reaches the P20R pockets
The substrate absorbs the nutrients and delivers them to the roots by capillarity
At the end of the cycle, the system flushes with pure water for 2 minutes to clean the capillaries
Precise dosing
The 0–100% analog dial allows fine adjustment of the concentration. It does not rely on electronics — it works even without internet or an active controller.
Agitation pump
Keeps the nutrient solution homogeneous inside the barrel, preventing chelate sedimentation and ensuring a consistent dose in every cycle.
Compatible with all systems
It integrates with the irrigation system with no changes to the hydraulics. The injection point is installed after the Hydro ONE or the main solenoid.
Full chemical resistance
PVDF+FP+PTFE withstands concentrated fertilizers, fulvic acids, chelated EDTA and the hypochlorite used in periodic system cleaning.
Preventive maintenance
Keeping the system in shape.
Recommended weekly cleaning
At the end of the last irrigation of the week, replace the barrel solution with clean water
Run a full irrigation cycle with pure water (capillary flush)
Turn off the agitation pump and drain the barrel
Inspect the EMEC inlet tube — clean it with a soft sponge if there is any deposit
Replacing the PTFE check valves (annual)
Switch off the 220V power supply
Close the upstream water valve and release the pressure
Disconnect the Ø 4×6mm inlet and outlet tubes
Unscrew the front head (4 screws)
Replace the PTFE ball valves (original EMEC kit)
Check the FP diaphragm — replace it if there is any cracking or deformation
Reassemble the head with uniform torque and test without pressure for 5 minutes
Use only original EMEC parts
Generic valves and diaphragms do not withstand the chemical solutions used in Plante fertigation and may contaminate the system with particles of degraded material. Request the EMEC maintenance kit for the EMEC FCE 0505 K.
When the problem persists
Plante 24-hour technical support.
Before reaching out, have the pump model (FCE 0505 K), the type of nutrient used, the solution concentration and photos of the installation at hand. These elements make up the forensic package of the call and speed up the diagnosis.
Warranty conditional on preventive maintenance
The EMEC pump warranty is valid when the weekly cleaning protocol is followed and only original parts are used. Plante carries out a biannual technical inspection visit included in the Plante Care plan.
Are you an architect or builder?
Bring a Plante vertical garden to your project. See the portfolio of large-scale projects and talk to me.
What is automatic fertigation in a vertical garden?
Fertigation delivers nutrients directly in the irrigation water, at the moment the plants need them. Plante's system uses the EMEC FCE 0505 K electromagnetic dosing pump to inject concentrated fertilizer into the water flow, and an agitation pump in the nutrient barrel to keep the solution homogeneous.
How is the dose adjusted?
With the front dial, from 0 to 100%. It is analog: no additional electronics or external controller are needed, and it works even without internet.
What happens at the end of each cycle?
The system flushes with pure water for 2 minutes to clean the capillary tubes.
Does it require changes to the existing irrigation?
No. It integrates with the irrigation system with no changes to the hydraulics. The injection point is installed after the Hydro ONE or the main solenoid.
What maintenance does it need?
Weekly cleaning is recommended, and the PTFE check valves are replaced once a year.
Is there technical support?
Yes. Plante offers 24-hour technical support.
Want this product on your project?
Tell us the size and location. We reply with the right system and a quote, no list prices.
